How To Open Flash Drive On Windows Xp

How to Setup Windows XP from USB drive?

You are here: Tutorials > How to setup Windows XP from USB drive?

Step1: Creating Rescue USB Drive

First, we need create a rescue USB bulldoze which can boot the computer. Delight follow the steps,

Run PowerISO rescue media utility. You can download it hither. On Windows Vista or in a higher place operating system, you may need confirm the UAC dialog to continue.
Insert the USB drive you intend to kicking from.
The utility will allow you cull Windows PE architecture and version. It is suggested to select 32-bit architecture and Windows PE 3.11. Click "Next" to continue.
Select USB bulldoze for output device, and select the correct drive from the list. Click "Next" to proceed.

The utility volition commencement creating rescue USB drive. It volition cheque necessary component and automatically download missing component from the server.

Delight find that all existing data on the USB drive will exist destroyed during this step. The program will warning you before writing the USB drive. Click "OK" to continue.

When it's done, copy the Windows XP setup files to the USB drive. Please note that you lot'll only need the i386 folder.

If no errors occurred in the above process, you should now be all gear up to setup Windows XP from USB drive!

Step 2: Configuring the BIOS

You should now reboot and get into the BIOS configuration to boot from USB. Instructions for doing and so vary wildly from organisation to organisation, but more often than not entail the following:

Reboot the system.
While booting (before Windows starts loading), go into the BIOS configuration screen by hitting something similar F1, F2, Delete or Escape. Hotkey instructions are by and large provided on the screen.
Become to the section that contains your kicking devices.
With your USB drive plugged in, the USB drive should exist listed. If it isn�t, your system might non back up booting from USB. Assuming that information technology is supported (as is the case with about all modern hardware), promote your USB drive to the master boot device.
Go out from the BIOS configuration, saving all changes.

Please detect that y'all can seriously screw up your system by providing incorrect BIOS settings!

Stride three: Booting from rescue USB bulldoze

Bold that you properly configured your BIOS and your USB drive supports booting, your computer should now kick from the the rescue USB drive. Depending on the speed of your USB drive, this may have a while.

If it isn�t working, then double-check the following before making a scene:

Is your BIOS properly configured for booting from the USB device? (Is the USB device listed and does information technology have meridian priority?)
Have you correctly prepared the USB drive in footstep one? (Restart the procedure.)
Does your USB drive properly support being booted from? (Try another one!)

Step 4: Prepping the Hard disk

Yous demand to brand sure that your difficult drive is partitioned and formatted properly. Especially if you've had Linux or some other operating arrangement on it, you'll need to repartition and format it. The rescue drive contain file manager and command line utility. You tin launch DiskPart for disk partitioning and formatting from the control utility.

If you are sure that your difficult bulldoze is prepare up properly (i.east. it has only run Windows, it contains a valid FAT or NTFS partitioning) then you can rubber yourself the hassle and skip this pace.

Window XP doesn't support GPT partitioning. If your hard drive is partitioned in GPT mode, you also demand repartition and format the disc.

To repartition and format (This procedure will destroy any data on the difficult bulldoze):

Click the icon on job bar to launch a command line Window.
Enter DiskPart to run the congenital-in disk direction utility.
Enter the commands needed to repartition and format your drive. For example, try the post-obit:

select disk 0 (select the kickoff disk. On your computer, disk 0 may not be the right disk, you tin can utilise "list disk" to find the correct deejay.)

make clean (purges the unabridged drive, essentially resetting it)

create segmentation master (creates a single partition from the entire disk)

select partition1 (select the partition created)

format fs=ntfs quick (format the partitioning to NTFS organization, and exercise a chop-chop format)

assign (assign the partition a drive letter)

exit (quits DiskPart).

Stride v: Launching Windows XP Setup from USB bulldoze

With your drive all set, y'all can now launch the Windows XP setup with a few custom parameters. Let'due south assume that the files are bachelor at E:\i386.

Plugging in a device now won�t piece of work. Recollect that all USB devices will need to be plugged in right from the start while using the rescue drive.

Run the following control:

Run E:\i386\winnt32.exe /syspart:C: /tempdrive:C: /makelocalsource. Supercede C: with the drive you want to install Windows to.
Proceed with the installation. If asked to convert the installation volume to NTFS, reply No. The setup program incorrectly believes that your USB drive (if is formatted as FAT) needs conversion.

The setup programme volition then silently close, which might make you think that something went wrong. Don't worry though.

Step vi: Go on Windows XP Setup from Hard disk drive

Reboot your system.
Unplug USB drive during post phase.
Modify your BIOS settings dorsum to kick from hard disk again every bit needed.
Yous can now keep to finish setting upwardly Windows XP.

Note: The above guide works with Windows XP only. For Windows x, Windows 7, Windows 8 / viii.i, or Windows Vista operating systems, please refer to some other guide at http://world wide web.poweriso.com/tutorials/how-to-brand-win7-bootable-usb-drive.htm .

Source: https://www.poweriso.com/tutorials/how-to-make-winxp-bootable-usb-drive.htm

Posted by: daviescritaiment1967.blogspot.com